Q: Is the Yard Master Wireless RF remote rechargeable or does it use batteries?
The RF remote is not rechargeable and requires one button cell CR2032 battery.
Remotes & Controls FAQ’s
Q: Where Can I find the IR codes for my Electric Screen IR remote?
Elite provides binary codes for the IR remote, see below. Series Up Stop Down CineTension 2 Series 1111 0000 0001 1111 0000 0010 1111 0000 0100 Evanesce / Evanesce Tab-Tension B 1111 0000 0001 1111 0000 0010 1111 0000 0100 Home2 Series 1111 0000 0001 1111 0000 0010 1111 0000 0100 Spectrum Series 1111 0000…
What are the Hex codes for Elite’s V2.0 infrared remotes?
Please see the codes listed below. UP (Protocol: F12 Device Code: 07.01 Function: 40) 0000 006D 0018 0000 0030 0011 0030 0011 0030 0011 0030 0011 0010 0031 0010 0031 0010 0031 0010 0031 0010 0031 0010 0031 0030 0011 0010 053E 0030 0011 0030 0011 0030 0011 0030 0011 0010 0031 0010 0031 0010 0031…
What is the voltage output of the IR remote?
The output voltage is 3 volts and wattage is 3 milliwatts
How do I sync my RF remote to my Elite electric screen
If your RF remote control does not work with your screen, try the following to get in synced. See below for instructions. Make sure new batteries or working batteries are in your RF remote control before proceeding with the steps. For V 2.0 electric screens. The version number can be found on the remote control, the sticker on…
What is the voltage output of the RF remote?
A: The output voltage is 3 volts and the wattage is 3 milliwatts
What is the frequency of your RF remote?
The frequency of the RF remote is 433MHz
What is the difference between an IR and an RF remote control?
The IR remote is an InfraRed remote. Infrared is based on the “light” part of the electromagnetic spectrum. The RF remote is a Radio Frequency remote. Radio frequency is based on the “radio” section of the electromagnetic spectrum. While the IR remote control requires direct aim to the receiver in order for the signal to…
My projector does not have a 12V trigger port, but it does have a USB Port. Is there a way to sync my Elite Screens Motorize screen to projector’s power cycle and enable drop/rise operation?
Yes there is. You will need to splice your USB cable with an RJ45 cable. A USB has 4 wires, but you will only need the red and black. Splice them to the RJ45 orange and green wires and connect the USB. See diagram below for reference. NOTE: If you are using your own RJ45, please use…
My screen is receiving RF interference, is there a way to reset the circuit board?
Yes, version 2.0 screens have a reset button located on the circuit board which helps eliminate RF interference. Please Click Here for instructions on how to locate the circuit board on your screen.
How do I connect my Elite Screens ZSP-12 volt trigger RJ-45 adaptor to my projector and how does it work?
See diagram below for wiring information. Download and print this drawing (PDF) How to set up and install a ZSP-12V projector trigger [kad_youtube url=”https://youtu.be/_jUeSYK-TnU” hidecontrols=”true”]
Q: Can I Interface my 5-12V Trigger with an AC Power Switch?
There’s a couple of suggestions. If controlling your screen’s drop and rise with a light switch, we offer our (ZIW) integrated wall switch that will work just fine with your electric projection screen. To operate the projection screen using the 12-Volt trigger, We recommend connecting the trigger’s RJ45 connection to your projector since it was designed solely for that…