Q: Can I buy a small screen material sample?
A: Yes, you can buy a screen material sample by clicking here.
Q: Regarding the Yard Master 2 / Yard Master 2 WraithVeil Dual / Yard Master Plus Series products, Is there an issue with leaving the screen on the frame for long periods of time? Will the screen stretch out? Will the frame eventually warp? I’m looking to avoid constant assembly and disassembly.
A: The Yard Master 2 / Yard Master 2 WraithVeil Dual / Yard Master Plus Series products are portable outdoor screens that can be left in a safe area outside for a few nights. It is not designed to be a permanent fixed frame and left assembled for a long period of time indoors or outdoors.
Q: Do we recommend they store the Elite Yard Master portable Projection screen in a plastic or a metal bin when it is not being used ?
A: Either way will work just fine. However, it is best to first pack the screen into its canvas carrying pouch which is included. This accessory was designed to protect the screen when you store it.
Q. Is there a basic method of cleaning this Elite projection material?
A: Yes, we recommend cleaning the screen with a lukewarm solution of mild soap and water.
Q: After storing my DIY Screen, there are creases/wrinkles left on the material. Is there any way I can remove or limit the amount of creases?
A: The DIY screen material may have creases or wrinkles after it has been stored for an extended period of time. These are known as memory lines. This is both a normal and correctable phenomenon. The creases/wrinkles on the DIY material will disappear in most cases if the material is stretched out for about 24-48 hours. After that time has passed, the lines should vanish. To speed up the process of crease/wrinkle removal, you can try applying heat to the material (example: a blow dryer at low heat). If attempting to do this, please move the heat source across the material to avoid having the heat directly on one spot for a long time.
Q: What are the model numbers in the DIY Series?
A: Here is a complete list of the model numbers in the DIY Series: DIY94V*, DIY145V*, DIY193V*, DIY114H*, DIY133H*, DIY236H*, DIY96RH*, DIY141RH*, DIY171RH*, DIY251RH*, DIY100RV*, DIY132RV*, DIY148RV*, DIY195RV*. (*Denotes a discontinued model number)
Q: Can the DIY Pro and DIY Pro REAR Series be used indoors?
A: Yes, Both the DIY Pro and DIY Pro REAR can also be used indoors.
Q: After storing my DIY Screen, there are creases/wrinkles left on the material. Is there any way I can remove or limit the amount of creases?
A: The DIY screen material may have creases or wrinkles after it has been stored for an extended period of time. These are known as memory lines. This is both a normal and correctable phenomenon. The creases/wrinkles on the DIY material will disappear in most cases if the material is stretched out for about 24-48 hours. After that time has passed, the lines should vanish. To speed up the process of crease/wrinkle removal, you can try applying heat to the material (example: a blow dryer at low heat). If attempting to do this, please move the heat source across the material to avoid having the heat directly on one spot for a long time.
Q: What are the model numbers for the DIY PRO Series?
A: Here is a full list of the model numbers in the DIY Pro Series: DIY94V1, DIY145V1, DIY193V1, DIY114H1, DIY133H1, DIY236H1, DIY96RH1, DIY123RH1, DIY141RH1, DIY100RV1, DIY132RV1, DIY148RV1, DIY195RV1
Q: Can the DIY Pro Dual Series be used indoors?
A: Yes, the DIY Pro Dual can also be used indoors.
Q: What are the model numbers for the DIY PRO Dual Series?
A: Here is a full list of the model numbers in the DIY Pro Dual Series: DIY96RH1-DUAL, DIY123RH1-DUAL
Q: Does the DIY Wall 3 series screen have black masking borders
A: Yes, the DIY Wall 3 series screen black masking borders. Please refer to the dimensions tables for the amount of black masking for individual models.
Q: How do I hang the DIY Wall 3 screen?
A: The DIY Wall 3 screen can be hung from nails or screws installed on the wall using the built-in wall hooks on both top and bottom support bars.
Q: What are the model numbers is the DIY Wall 3 Series?
A: Here is a full list of the model numbers in the DIY Wall 3 Series: DIYW100H3, DIYW116H3, DIYW135H3, DIYW150H3
Q: How do you properly fold the net base?
Q: Will my Yard Master 2 projection screen rust if I leave it outdoors for a long period of time (weeks, etc.)?
A: Eventually, yes. It is recommended that no projection screen, regardless of manufacturer/model be permanently left outside and exposed directly to the elements. The yardmaster is made for temporary outdoor events such as day excursions or weekend camping trips. It has an aluminum frame that is coated in a rust-resistant black enamel for outdoor events. Just like any other piece of audio-video equipment, proper care and storage is required to maximize the Yardmaster’s operational lifespan.
Q: What are the model numbers for the Yard Master 2 Series?
A: Here is a full list of the model numbers in the Yard Master 2 Series: OMS100H2, OMS120H2, OMS100HR2, OMS120HR2
Q: Are the legs and frame on the Yard Master and Yard Master 2 Series adjustable?
A: No, both the Yard Master and Yard Master 2 Series have a fixed height and length for all leg and frame parts included. The Yard Master 2 Series, however, does have optional extension legs that can be purchased to increase the bottom viewing area. Please click here for more information.
Q: Can I use the YardMaster 2 series outside on a windy day?
A: In a calm wind below 10mph, yes. If it exceeds the 10mph, there is a chance of damaging the frame or the material itself.
Q: How do I alleviate screen creases?
A: The Yard Master 2 screen material is folded so that it can fit into a smaller package to decrease freight cost. If you notice crease lines on the material upon opening the box, there are a couple of things that can be done to alleviate them. The easiest method would be to allow the material to stretch on the Yard Master 2 frame. Over time, the creases will alleviate to a minimal.
If after a few days you do not see any improvement, the second method in alleviating them would be the use of a hairdryer. Set the dryer on medium heat and blow on the material from its back side from about 3 feet away, concentrating only on the crease lines. Do not apply excessive heat as this will cause for the material to deform. You may need to repeat this process for a couple of consecutive days depending on the severity of the creases.
Q: What are the model numbers for replacement CineWhite® screen material for my YardMaster 2 screen?
A: Elite Screens offers replacement CineWhite® material for the YardMaster 2 Series. Here is a complete list of the model number for replacement CineWhite® Material: Z-OMS90H2, Z-OMS1000H2, Z-OMS110H2, Z-OMS120H2, Z-OMS135H2 Decoding the model number: Z-OMS 90 H 2
- Z- Replacement Material
- OMS- YardMaster Outdoor design (Version 2)
- 90= Diagonal Size of 90"
- H= 16:9 Aspect Ratio
- 2=YardMaster 2 Series
Q: How many times do we recommend the Elite Yard Master Portable Projector screen material to be folded so it can be properly stored after each use? Is there a preferred number of folds to reduce the presence of wrinkles?
A: In order to have less memory lines or “wrinkles” from folding, here are a few tips. Don’t fold tightly or try to fold over the material as compact as possible. Both will leave pronounced memory lines. It is recommended to take note of how lightly folded the screen material was when it came from the factory and repeat that whenever you are packing the screen away. Another method when storing the screen is to gently and loosely roll the material and keep it in a safe, dry space at an optimal room temperature.
Q: Should the Projection screen be kept in a cool dry place ? or should it be kept warm?
A: The material is well-made and designed to last so either storage method will work just fine. That said, make sure that the material is dry before packing it away so that the material won’t be imprinted and waterborne sediment won’t build up and soil the screen. Storing the material at an optimal room temperature will ensure that the screen will be suitably pliable enough to stretch onto the framework without much effort. Storing the screen in a cool place won’t hurt the material but it does make the material a little tougher to stretch over the frame when assembling.
Q: Do we recommend they store the Elite Yard Master portable Projection screen in a plastic or a metal bin when it is not being used ?
A: Either way will work just fine. However, it is best to first pack the screen into its canvas carrying pouch which is included. This accessory was designed to protect the screen when you store it.
Q: What is the proper way to disassemble the Yard Master 2?
A: Below are the steps to disassemble your screen. For the full Yard Master 2 user guide, click here.
- Remove ropes (G) and stakes (I) from the ground.
- Unlatch the hinged support bars on front side of each leg so that it is bent and fold that half of the legs up for the next step.
- Slowly lower the screen to the ground (towards the closed legs). Two people are needed for this step.
- Unlatch the hinged support bars and fold down other half of legs.
- Loosen and remove the ropes, knob screws (E) and eyebolts (F) from each leg.
- Remove the frame legs (B) from the folding frame (A).
- Detach the screen material (D) from the folding frame (A) by carefully unsnapping each button as shown.
- Fold screen material (D) in half, folding the bottom of the screen towards the top. Then, fold in half again in the same way. Lastly, fold the material into thirds to condense the length, see user guide for visual. *If you prefer to roll the material, instead of folding into thirds, roll from one end to the other after folding in half twice.
- Unlatch the hinged support bars in each corner of the folding frame (A).
- Press in the silver locking buttons, near the folding joints, and slowly gather the sides of the folding frame
- Again, press in the silver locking buttons. Then, pick up one end of the folding frame, and walk it to the other end, folding the longer sections into thirds.
- Store the screen in the provided carrying bag (h). Be sure to place folding frame, legs, and smaller parts into the carrying bag first and place the material on top to keep material from creasing or tearing.
Q: Are leg extensions available for the Yard Master 2 to increase the bottom viewing area?
A: Yes, optional extension legs can be purchased to increase the bottom viewing area. Please click here for more information.
Q: How many times do we recommend the Elite Yard Master Portable Projector screen material to be folded so it can be properly stored after each use? Is there a preferred number of folds to reduce the presence of wrinkles?
A: In order to have less memory lines or “wrinkles” from folding, here are a few tips. Don’t fold tightly or try to fold over the material as compact as possible. Both will leave pronounced memory lines. It is recommended to take note of how lightly folded the screen material was when it came from the factory and repeat that whenever you are packing the screen away. Another method when storing the screen is to gently and loosely roll the material and keep it in a safe, dry space at an optimal room temperature.
Q: Should the Projection screen be kept in a cool dry place ? or should it be kept warm?
A: The material is well-made and designed to last so either storage method will work just fine. That said, make sure that the material is dry before packing it away so that the material won’t be imprinted and waterborne sediment won’t build up and soil the screen. Storing the material at an optimal room temperature will ensure that the screen will be suitably pliable enough to stretch onto the framework without much effort. Storing the screen in a cool place won’t hurt the material but it does make the material a little tougher to stretch over the frame when assembling.
Q: Do we recommend they store the Elite Yard Master portable Projection screen in a plastic or a metal bin when it is not being used ?
A: Either way will work just fine. However, it is best to first pack the screen into its canvas carrying pouch which is included. This accessory was designed to protect the screen when you store it.
Q: What is the proper way to disassemble the Yard Master 2?
A: Below are the steps to disassemble your screen. For the full Yard Master 2 user guide, click here.
- Remove ropes (G) and stakes (I) from the ground.
- Unlatch the hinged support bars on front side of each leg so that it is bent and fold that half of the legs up for the next step.
- Slowly lower the screen to the ground (towards the closed legs). Two people are needed for this step.
- Unlatch the hinged support bars and fold down other half of legs.
- Loosen and remove the ropes, knob screws (E) and eyebolts (F) from each leg.
- Remove the frame legs (B) from the folding frame (A).
- Detach the screen material (D) from the folding frame (A) by carefully unsnapping each button as shown.
- Fold screen material (D) in half, folding the bottom of the screen towards the top. Then, fold in half again in the same way. Lastly, fold the material into thirds to condense the length, see user guide for visual. *If you prefer to roll the material, instead of folding into thirds, roll from one end to the other after folding in half twice.
- Unlatch the hinged support bars in each corner of the folding frame (A).
- Press in the silver locking buttons, near the folding joints, and slowly gather the sides of the folding frame
- Again, press in the silver locking buttons. Then, pick up one end of the folding frame, and walk it to the other end, folding the longer sections into thirds.
- Store the screen in the provided carrying bag (h). Be sure to place folding frame, legs, and smaller parts into the carrying bag first and place the material on top to keep material from creasing or tearing.
Q: Will my Yard Master 2 projection screen rust if I leave it outdoors for a long period of time (weeks, etc.)?
A: Eventually, yes. It is recommended that no projection screen, regardless of manufacturer/model be permanently left outside and exposed directly to the elements. The yardmaster is made for temporary outdoor events such as day excursions or weekend camping trips. It has a rolled sheet steel alloy frame that is coated in a rust-resistant black enamel for outdoor events. Just like any other piece of audio-video equipment, proper care and storage is required to maximize the Yardmaster’s operational lifespan.
Q: What are the model numbers for the Yard Master 2 Rear Series?
A: Here is a full list of the model numbers in the Yard Master 2 Series: OMS100HR2, OMS120HR2
Q: Can I use the YardMaster 2 series outside on a windy day?
A: In a calm wind below 10mph, yes. If it exceeds the 10mph, there is a chance of damaging the frame or the material itself.
Q: How do I alleviate screen creases?
A: The Yard Master 2 screen material is folded so that it can fit into a smaller package to decrease freight cost. If you notice crease lines on the material upon opening the box, there are a couple of things that can be done to alleviate them. The easiest method would be to allow the material to stretch on the Yard Master 2 frame. Over time, the creases will alleviate to a minimal.
If after a few days you do not see any improvement, the second method in alleviating them would be the use of a hairdryer. Set the dryer on medium heat and blow on the material from its back side from about 3 feet away, concentrating only on the crease lines. Do not apply excessive heat as this will cause for the material to deform. You may need to repeat this process for a couple of consecutive days depending on the severity of the creases.
Q: Are the legs and frame on the Yard Master and Yard Master 2 Series adjustable?
A: No, both the Yard Master and Yard Master 2 Series have a fixed height and length for all leg and frame parts included. The Yard Master 2 Series, however, does have optional extension legs that can be purchased to increase the bottom viewing area. Please click here for more information.
Q: Are leg extensions available for the Yard Master 2 to increase the bottom viewing area?
A: Yes, optional extension legs can be purchased to increase the bottom viewing area. Please click here for more information.
Q: Will my Yard Master projection screen rust if I leave it outdoors for a long period of time (weeks, etc.)
A: Eventually, yes. It is recommended that no projection screen, regardless of manufacturer/model be permanently left outside and exposed directly to the elements. The yardmaster is made for temporary outdoor events such as day excursions or weekend camping trips. It has a rolled sheet steel alloy frame that is coated in a rust-resistant black enamel for outdoor events. Just like any other piece of audio-video equipment, proper care and storage is required to maximize the Yardmaster’s operational lifespan.
Q: My Yard Master has lines or wrinkles on the material. Will they disappear after stretching or what else can I do to eliminate them?
A: Wrinkles or lines found on the Yard Master projection material in most cases disappear when the material is stretched over the frame. If in case they don't, we recommend using a fabric steamer to eliminate any lines or wrinkles.
Q: What are the model numbers in the Yard Master Series?
A: Here is a full list of the model numbers in the Yard Master Series: OMS100HR, OMS120HR, OMS100H, OMS120H, OMS150H, OMS180H1, OMS200H1
Q: Are the legs and frame on the Yard Master and Yard Master 2 Series adjustable?
A: No, both the Yard Master and Yard Master 2 Series have a fixed height and length for all leg and frame parts included. The Yard Master 2 Series, however, does have optional extension legs that can be purchased to increase the bottom viewing area. Please click here for more information.
Q: Are leg extensions available for the Yard Master 2 to increase the bottom viewing area?
A: Yes, optional extension legs can be purchased to increase the bottom viewing area. Please click here for more information.
Q: What makes the Yard Master Electric IP33 Certified?
A: For a quick explanation on the IP33 rating, please click here.
Q: Is there a way to trigger the Yard Mater Electric/Tension screen’s UP/DOWN operation other than through Radio Frequency? I am trying to send an IR sensor or 12 volt signal from a Control4 platform. Is there a way to do so without using the 12 volt RF wireless adapter? I have the adapter that came with the screen, however, the projector we are using does not have a 12-volt trigger output.
A: All Yard Master Electric Screens only use Radio Frequency to control the screen’s operation.
If you have a projector that does not have a dedicated 12v trigger output port, you can use the ZOMS-TR12V-V2. This wireless 12v trigger accessory is included with all Yard Mater Electric/Tension with serial numbers beginning with 19AE and newer. The ZOMS-TR12V-V2 plugs to the projector’s power terminal so no 12v projector trigger is required. Please click here for instructions on how to program the ZOMS-TR12V-V2.
Q: How can I sync RF remote to my Yard Master Electric / Yard Master Electric Tension screen?
A: Here are the instructions on how to sync your RF remote. Radio Frequency (RF) Remote Synchronization Instructions for: ZOMS-RF-W-V1.0 and ZOMS-RF-W-V2.0
- Unplug the screen’s power cable from the power outlet.
- Press and HOLD the UP button on the RF remote
- While holding the UP button, plug the screen’s power cable back into the power outlet. a. You should hear a single “beep” when the power cable has been plugged in, indicating it has entered pairing mode.
- After hearing a set of multiple “beeps”, release UP button for 2 seconds, then press UP button again.
- You should now be able to control your electric screen with the RF remote control.
- If unsuccessful repeat from Step 1.
Q: Is there a way to trigger the Yard Mater Electric/Tension screen’s UP/DOWN operation other than through Radio Frequency? I am trying to send an IR sensor or 12 volt signal from a Control4 platform. Is there a way to do so without using the 12 volt RF wireless adapter? I have the adapter that came with the screen, however, the projector we are using does not have a 12-volt trigger output.
A: All Yard Master Electric Screens only use Radio Frequency to control the screen’s operation.
If you have a projector that does not have a dedicated 12v trigger output port, you can use the ZOMS-TR12V-V2. This wireless 12v trigger accessory is included with all Yard Mater Electric/Tension with serial numbers beginning with 19AE and newer. The ZOMS-TR12V-V2 plugs to the projector’s power terminal so no 12v projector trigger is required. Please click here for instructions on how to program the ZOMS-TR12V-V2.
Q: How can I sync RF remote to my Yard Master Electric / Yard Master Electric Tension screen?
A: Here are the instructions on how to sync your RF remote. Radio Frequency (RF) Remote Synchronization Instructions for: ZOMS-RF-W-V1.0 and ZOMS-RF-W-V2.0
- Unplug the screen’s power cable from the power outlet.
- Press and HOLD the UP button on the RF remote
- While holding the UP button, plug the screen’s power cable back into the power outlet. a. You should hear a single “beep” when the power cable has been plugged in, indicating it has entered pairing mode.
- After hearing a set of multiple “beeps”, release UP button for 2 seconds, then press UP button again.
- You should now be able to control your electric screen with the RF remote control.
- If unsuccessful repeat from Step 1.
Q: What makes the Yard Master Manual IP65 Certified?
A: For a quick explanation on the IP65 rating, please click here. 
Q: How many times do we recommend the Elite Yard Master Portable Projector screen material to be folded so it can be properly stored after each use? Is there a preferred number of folds to reduce the presence of wrinkles?
A: In order to have less memory lines or “wrinkles” from folding, here are a few tips. Don’t fold tightly or try to fold over the material as compact as possible. Both will leave pronounced memory lines. It is recommended to take note of how lightly folded the screen material was when it came from the factory and repeat that whenever you are packing the screen away. Another method when storing the screen is to gently and loosely roll the material and keep it in a safe, dry space at an optimal room temperature.
Q: Should the Projection screen be kept in a cool dry place ? or should it be kept warm?
A: The material is well-made and designed to last so either storage method will work just fine. That said, make sure that the material is dry before packing it away so that the material won’t be imprinted and waterborne sediment won’t build up and soil the screen. Storing the material at an optimal room temperature will ensure that the screen will be suitably pliable enough to stretch onto the framework without much effort. Storing the screen in a cool place won’t hurt the material but it does make the material a little tougher to stretch over the frame when assembling.
Q: Do we recommend they store the Elite Yard Master portable Projection screen in a plastic or a metal bin when it is not being used ?
A: Either way will work just fine. However, it is best to first pack the screen into its canvas carrying pouch which is included. This accessory was designed to protect the screen when you store it.