TAB-Tensioned Outdoor MOTORIZED PROJECTION SCREEN

Yard Master Electric Tension Series

Award_winning
IP33 Certified Projector Screens

The Yard Master Electric Tension Series is an electric screen with 2-way projection material that is IP33 rated for wind/rain penetration for outdoor applications. The tab-tension design supports a front/rear projection surface with perfect uniform flatness. This allows you to use either a standard, short throw or UST projectors. The WraithVeil® Dual material provides superb image clarity from in-front or behind and its diverse projector compatibility makes it a must for outdoor home or commercial video applications. It is ideal for nighttime movie presentations. The screen comes with a Radio Frequency remote control that doubles as a wireless 12-volt projector trigger that coordinates the screen’s drop and rise with the projector’s power cycle.

How to Synchronize RF Remote to Yard Master Electric Screens

Yard Master Electric Tension Series Outdoor Dual Projector Screen in Fresno, CA

Yard Master Electric Tension Indoor/Outdoor Wall/Ceiling Projection Screen Testimonial

Yard Master Electric Tension Outdoor Projection Screen Product Review by JoelsterG4K

Screen Material

  • WraithVeil® Dual is a 2-directional front/rear projection material
  • 0.8 Gain brightness with a 150° viewing angle on either side
  • Designed for outdoor use without compromising its home theater visual appeal
  • Standard 4-side black masking borders absorb projector overshoot while enhancing visual contrast (Front side ONLY)
  • Compatible with Standard, Short, and Ultra-Short Throw Projectors
    (Check EliteProjector® Ultra-Short Throw Projector)
  • Compatible with Full HD, Ultra HD (4K/8K) and Active 3D projectors.
  • Available in diagonal sizes 100”/120”/135” and 150” with a 16:9 aspect ratio

 

Design and Installation

  • Dynamic indoor home theater quality with the durability of an outdoor product
  • Ideal for backyards, patios, pool decks, and recreation room installations
  • Rust resistant aluminum floating brackets allow flush wall/ceiling installations to be perfectly centered
  • Floating eyebolt construction enables hanging installations
  • Tab-tension design provides uniform flatness over the entire screen surface for use with standard, short-throw and UST projectors
  • Radio Frequency remote for long range operation without line of sight required
  • Wireless 12-volt projector trigger included to synchronize the projector’s power cycle for drop/rise operation of the screen

 

Quality and Reliability

  • Rust-proof metal components – housing, roller tube, brackets, and weight bar
  • Tubular motor allows swift operation and superior weight tolerance and lifespan
  • 2-year limited warranty, and 3-year warranty for ENR-G – Education, Non-profit, Religious and Government/Military organizations
  • Lifetime Tech Support by Elite Screens Professional Service Team through Email, Phone or Online Form.

Choosing The Right Sized Projection Screen

Selecting the Right Elite Screens Screen Material For Your Home Theater

Understanding ANSI Lumens & Screen Gain

Understanding Aspect Ratio & Resolution

4K/UltraHD: What You Need To Know

GreenGuard® Certification – Improving Human Health and Quality of Life

Projection Screen to HDTV Comparison

How To Perfectly Install ANY Projection Screen

The Right Projection Screen for UST Projectors

Ceiling and Ambient Light Rejecting (CLR/ALR) Projection Screen Setup Guide

Outdoor Screen Accessories

Q: After following the instructions on syncing the ZOMS-T12V to my screen, it only dropped 1” and it quickly deployed back in to the housing. How do I complete the syncing process?
Q: After following the instructions on syncing the ZOMS-T12V to my screen, it only dropped 1” and it quickly deployed back in to the housing. How do I complete the syncing process?

After the screen closes upon the initial syncing process, simply turn off the projector’s power cycle, and restart it again. When the projector turns back on, the screen will deploy to its fullest extent.

Q: How do I synchronize the ZOMS-T12V Projector Trigger to my Elite electric screen?
Q: How do I synchronize the ZOMS-T12V Projector Trigger to my Elite electric screen?

Wireless 12V Trigger for Yard Master Electric – ZOMS-TR12V
For the instructional guide on synchronizing the ZU12V, please click here.

Q : How can I sync RF remote to my Yard Master Electric / Yard Master Electric Tension screen?
How can I sync RF remote to my Yard Master Electric / Yard Master Electric Tension screen?

Here are the instructions on how to sync your RF remote. Radio Frequency (RF) Remote Synchronization Instructions for: ZOMS-RF-W-V1.0 and  ZOMS-RF-W-V2.0

1. Unplug the screen’s power cable from the power outlet.
2. Press and HOLD the UP button on the RF remote
3. While holding the UP button, plug the screen’s power cable back into the power outlet. a. You should hear a single “beep” when the power cable has been plugged in, indicating it has entered pairing mode.
4. After hearing a set of multiple “beeps”, release UP button for 2 seconds, then press UP button again.
5. You should now be able to control your electric screen with the RF remote control.
6. If unsuccessful repeat from Step 1.

Q : Is there a way to trigger the Yard Mater Electric/Tension screen’s UP/DOWN operation other than through Radio Frequency? I am trying to send an IR sensor or 12 volt signal from a Control4 platform. Is there a way to do so without using the 12 volt RF wireless adapter? I have the adapter that came with the screen, however, the projector we are using does not have a 12-volt trigger output.
Is there a way to trigger the Yard Mater Electric/Tension screen’s UP/DOWN operation other than through Radio Frequency? I am trying to send an IR sensor or 12 volt signal from a Control4 platform. Is there a way to do so without using the 12 volt RF wireless adapter? I have the adapter that came with the screen, however, the projector we are using does not have a 12-volt trigger output.

All Yard Master Electric Screens only use Radio Frequency to control the screen’s operation. If you have a projector that does not have a dedicated 12v trigger output port, you can use the ZOMS-TR12V-V2. This wireless 12v trigger accessory is included with all Yard Mater Electric/Tension with serial numbers beginning with 19AE and newer. The ZOMS-TR12V-V2 plugs to the projector’s power terminal so no 12v projector trigger is required.  Please click here for instructions on how to program the ZOMS-TR12V-V2.

Q: Is the Yard Master Wireless RF remote rechargeable or does it use batteries?
Q: Is the Yard Master Wireless RF remote rechargeable or does it use batteries?

The RF remote is not rechargeable and requires one button cell CR2032 battery.

Yard Mater Electric/Tension screens

Q: What is the operating temperature range for my outdoor Yard Master Electric/Manual projector screen?
Q: What is the operating temperature range for my outdoor Yard Master Electric/Manual projector screen?

50° – 104° F (10° – 40° C)

Q : How can I sync RF remote to my Yard Master Electric / Yard Master Electric Tension screen?
How can I sync RF remote to my Yard Master Electric / Yard Master Electric Tension screen?

Here are the instructions on how to sync your RF remote. Radio Frequency (RF) Remote Synchronization Instructions for: ZOMS-RF-W-V1.0 and  ZOMS-RF-W-V2.0

1. Unplug the screen’s power cable from the power outlet.
2. Press and HOLD the UP button on the RF remote
3. While holding the UP button, plug the screen’s power cable back into the power outlet. a. You should hear a single “beep” when the power cable has been plugged in, indicating it has entered pairing mode.
4. After hearing a set of multiple “beeps”, release UP button for 2 seconds, then press UP button again.
5. You should now be able to control your electric screen with the RF remote control.
6. If unsuccessful repeat from Step 1.

Q : Is there a way to trigger the Yard Mater Electric/Tension screen’s UP/DOWN operation other than through Radio Frequency? I am trying to send an IR sensor or 12 volt signal from a Control4 platform. Is there a way to do so without using the 12 volt RF wireless adapter? I have the adapter that came with the screen, however, the projector we are using does not have a 12-volt trigger output.
Is there a way to trigger the Yard Mater Electric/Tension screen’s UP/DOWN operation other than through Radio Frequency? I am trying to send an IR sensor or 12 volt signal from a Control4 platform. Is there a way to do so without using the 12 volt RF wireless adapter? I have the adapter that came with the screen, however, the projector we are using does not have a 12-volt trigger output.

All Yard Master Electric Screens only use Radio Frequency to control the screen’s operation. If you have a projector that does not have a dedicated 12v trigger output port, you can use the ZOMS-TR12V-V2. This wireless 12v trigger accessory is included with all Yard Mater Electric/Tension with serial numbers beginning with 19AE and newer. The ZOMS-TR12V-V2 plugs to the projector’s power terminal so no 12v projector trigger is required.  Please click here for instructions on how to program the ZOMS-TR12V-V2.

Q: What makes the Yard Master Electric IP33 Certified?
What makes the Yard Master Electric IP33 Certified?

For a quick explanation on the IP33 ratingIP33 Certified

Browse All FAQ Articles

2-year limited warranty, and 3-year warranty for ENR-G – Education, Non-profit, Religious and Government/Military organizations

Lifetime Tech Support by Elite Screens Professional Service Team through Email, Phone or Online Form.